National Instruments Digital Photo Keychain 12 Bit 200 MS s Digitizer User Manual

NI PXI/PCI-5124 Specifications  
12-Bit 200 MS/s Digitizer  
This document lists the specifications for the NI PXI/PCI-5124 (NI 5124)  
high-speed digitizer. Unless otherwise noted, these specifications are valid  
for the following conditions:  
All filter settings  
All impedance selections  
Sample clock set to 200 MS/s using onboard clock  
Typical values are representative of an average unit operating at room  
temperature. Specifications are subject to change without notice. For the  
most recent NI 5124 specifications, visit ni.com/manuals.  
To access the NI 5124 documentation, including the NI High-Speed  
Digitizers Getting Started Guide, which contains functional descriptions  
of the NI 5124 signals, navigate to Start»All Programs»National  
Instruments»NI-SCOPE»Documentation.  
Hot Surface If the NI 5124 has been in use, it may exceed safe handling temperatures and  
cause burns. Allow the NI 5124 to cool before removing it from the PXI chassis or PC.  
Analog Input (Channel 0 and Channel 1) ........................................ 2  
Front Panel Connector)................................................................. 17  
CLK OUT (Sample Clock and Reference Clock Output,  
Front Panel Connector)................................................................. 17  
Trigger..................................................................................................... 17  
Reference (Stop) Trigger ................................................................. 17  
TRIG (External Trigger, Front Panel Connector)............................ 19  
 
Specification  
Value  
Comments  
Voltage Levels  
Full Scale (FS)  
Input Range and  
Programmable  
Vertical Offset  
50 Ω  
1 MΩ  
Vertical  
Range  
Offset Range  
(V)  
Range  
Vertical Offset  
Range (V)  
(Vpk-pk  
)
(Vpk-pk  
0.2  
0.4  
1
)
0.2  
0.4  
1
0.1  
0.2  
0.5  
1
0.1  
0.2  
0.5  
2
2
1
4
2
4
2
10  
0
10  
20  
5
0
Maximum Input  
Overload  
50 Ω  
1 MΩ  
7 Vrms with |Peaks| 10 V  
|Peaks| 42 V  
Accuracy  
Resolution  
12 bits  
DC Accuracy  
(Programmable  
Vertical  
Range (Vpk-pk  
0.2 and 0.4  
)
NI PXI-5124  
NI PCI-5124  
Within 5 °C of  
self-calibration  
temperature  
(0.65% of Input  
+ 1.3 mV)  
(0.65% of Input  
+ 1.8 mV)  
Offset = 0 V)  
1 and 2  
(0.65% of Input  
+ 1.5 mV)  
(0.65% of Input  
+ 2.1 mV)  
4, 10, and  
20 (1 MΩ only)  
(0.65% of Input  
+ 10.0 mV)  
(0.65% of Input  
+ 10.0 mV)  
Programmable  
Vertical Offset  
Accuracy  
0.4% of offset setting  
Within 5 °C of  
self-calibration  
temperature  
© National Instruments Corporation  
3
NI PXI/PCI-5124 Specifications  
 
Specification  
Value  
50 Ω and 1 MΩ  
Comments  
DC Drift  
Range (Vpk-pk  
)
0.2, 0.4, 1, and 2  
(0.057% of Input + 0.006% of FS  
+ 100 μV) per °C  
4, 10, and  
20 (1 MΩ only)  
(0.057% of Input + 0.006% of FS  
+ 900 µV) per °C  
AC Amplitude  
Accuracy  
50 Ω  
1 MΩ  
Within 5 °C of  
self-calibration  
temperature  
0.06 dB  
( 0.7%) at 50 kHz  
0.09 dB  
( 1.0%) at 50 kHz  
Crosstalk,  
Typical  
–85 dB at 10 MHz  
CH 0 to/from  
CH 1, External  
Trigger to CH 0  
or CH 1  
Sparkle Code  
Rate, Typical  
<300 ppt* with onboard clock or 200 MHz external clock  
<3 ppt* with 150 MHz external clock  
Results based  
on 2 × 1012  
samples  
0 with 100 MHz external clock  
* ppt = parts per  
trillion (1012)  
Bandwidth and Transient Response  
Bandwidth  
(–3 dB)  
Range (Vpk-pk  
)
50 Ω  
1 MΩ  
Filters off  
* 135 MHz  
above 40 °C  
All ranges  
except 0.2  
150 MHz  
145 MHz up to  
40 °C*  
0.2  
85 MHz  
75 MHz  
Rise/Fall Time,  
Typical  
Range (Vpk-pk  
)
50 Ω and 1 MΩ  
Filters off  
All ranges  
except 0.2  
2.4 ns  
0.2  
3.3 ns  
Bandwidth  
Limit Filters  
Noise Filter  
Antialias Filter  
Only one filter  
can be enabled  
at any given  
time. The  
20 MHz, typical  
2-pole Bessel filter  
60 MHz, typical  
4-pole elliptical filter  
antialias filter  
is enabled by  
default.  
NI PXI/PCI-5124 Specifications  
4
ni.com  
 
Specification  
Value  
Comments  
AC Coupling  
Cutoff  
(–3 dB)  
12 Hz  
AC coupling  
available on  
1 MΩ only  
Passband  
Flatness  
Filter Settings  
Filters Off  
Range  
Referenced  
to 50 kHz  
(Vpk-pk  
)
50 Ω and 1 MΩ  
All  
0.5 dB DC to 20 MHz  
1.0 dB 20 MHz to 50 MHz  
ranges  
except  
0.2  
1.7 dB 50 MHz to  
100 MHz  
0.2  
0.6 dB DC to 20 MHz  
1.5 dB 20 MHz to 40 MHz  
Antialias  
Filter On  
All  
ranges  
–1.0 dB to +2.0 dB  
DC to 55 MHz  
2
1
0
–1  
–2  
–3  
–4  
–5  
–6  
–7  
–8  
–9  
Antialias  
Filter On  
Filters  
Off  
Noise Filter On  
–10  
1 M  
10 M  
Frequency (Hz)  
100 M  
200 M  
Figure 1. NI 5124 Frequency Response (Typical)  
© National Instruments Corporation  
5
NI PXI/PCI-5124 Specifications  
 
Specification  
Value  
Comments  
Spectral Characteristics  
Spurious-Free  
Dynamic Range  
with Harmonics  
(SFDR)  
(Physical),  
Typical  
Range  
Filters off  
or antialias  
filter on  
(Vpk-pk  
0.2  
0.4  
1
)
50 Ω  
1 MΩ  
70 dBc  
70 dBc  
70 dBc  
70 dBc  
67 dBc  
60 dBc  
60 dBc  
75 dBc  
75 dBc  
72 dBc  
72 dBc  
65 dBc  
65 dBc  
10 MHz,  
–1 dBFSinput  
signal  
Includes the  
2nd through  
the 5th  
2
4
harmonics  
10  
20  
Measured  
from DC to  
100 MHz on  
NI PXI-5124  
(1 MΩ only)  
Measured  
from 5 kHz to  
100 MHz on  
NI PCI-5124  
Total Harmonic  
Distortion  
(THD), Typical  
Range  
Filters off  
or antialias  
filter on  
(Vpk-pk  
0.2  
0.4  
1
)
50 Ω  
1 MΩ  
–74 dBc  
–74 dBc  
–72 dBc  
–72 dBc  
–63 dBc  
–63 dBc  
–68 dBc  
–68 dBc  
–68 dBc  
–67 dBc  
–66 dBc  
–58 dBc  
–58 dBc  
10 MHz,  
–1 dBFSinput  
signal  
Includes the  
2nd through  
the 5th  
2
4
harmonics  
10  
20  
(1 MΩ only)  
NI PXI/PCI-5124 Specifications  
6
ni.com  
 
Specification  
Value  
Comments  
Intermodulation  
Distortion,  
Typical  
0.2 Vpk-pk to 2.0 Vpk-pk Ranges on 50 Ω Input  
Filters off  
or antialias  
filter on  
–75 dBc  
Two tones at  
10.2 MHz and  
11.2 MHz  
Each tone is  
–7 dBFS  
Signal-to-Noise  
Ratio (SNR),  
Typical  
50 Ω  
1 MΩ  
Antialias  
Excludes  
harmonics  
Range  
Filters Antialias  
Filters  
Off  
10 MHz,  
–1 dBFSinput  
signal  
(Vpk-pk  
)
Off  
Filter On  
56 dB  
57 dB  
58 dB  
58 dB  
Filter On  
55 dB  
57 dB  
57 dB  
57 dB  
58 dB  
0.2  
0.4  
1
57 dB  
58 dB  
58 dB  
58 dB  
53 dB  
55 dB  
57 dB  
57 dB  
56 dB  
Measured  
from DC to  
100 MHz  
2
4
Signal to Noise  
and Distortion  
(SINAD),  
50 Ω  
Filters Antialias  
1 MΩ  
Includes  
harmonics  
Range  
Filters  
Off  
Antialias  
Filter On  
10 MHz,  
–1 dBFSinput  
signal  
(Vpk-pk  
)
Off  
Filter On  
56 dB  
57 dB  
58 dB  
58 dB  
Typical  
0.2  
0.4  
1
57 dB  
58 dB  
58 dB  
58 dB  
53 dB  
55 dB  
57 dB  
57 dB  
56 dB  
55 dB  
57 dB  
57 dB  
57 dB  
57 dB  
Measured  
from DC to  
100 MHz  
2
4
© National Instruments Corporation  
7
NI PXI/PCI-5124 Specifications  
 
0
–10  
–20  
–30  
–40  
–50  
–60  
–70  
–80  
–90  
–100  
–110  
9.83 MHz, –1 dBFS Input Signal  
1 M  
10 M  
20 M  
30 M  
40 M  
50 M  
60 M  
70 M  
80 M  
90 M  
100 M  
Frequency (Hz)  
Figure 2. NI 5124 Dynamic Performance, 50 Ω, 1 Vpk-pk Range,  
262,144 Point FFT (Typical)  
NI PXI/PCI-5124 Specifications  
8
ni.com  
 
Specification  
Value  
50 Ω  
Comments  
RMS Noise  
Range (Vpk-pk  
0.2  
)
1 MΩ  
Noise filter on  
50 Ω  
NI PXI-5124:  
94 μVrms  
(0.047% FS)  
NI PXI-5124:  
104 μVrms  
(0.052% FS)  
terminator  
connected  
to input  
NI PCI-5124:  
106 μVrms  
(0.053% FS)  
NI PCI-5124:  
116 μVrms  
(0.058% FS)  
0.4  
1
188 μVrms  
192 μVrms  
(0.047% FS)  
(0.048% FS)  
470 μVrms  
(0.047% FS)  
480 μVrms  
(0.048% FS)  
2
940 μVrms  
(0.047% FS)  
960 μVrms  
(0.048% FS)  
4
1.88 mVrms  
1.92 mVrms  
(0.047% FS)  
(0.048% FS)  
10  
4.7 mVrms  
4.8 mVrms  
(0.047% FS)  
(0.048% FS)  
20  
9.4 mVrms  
(1 MΩ only)  
(0.047% FS)  
© National Instruments Corporation  
9
NI PXI/PCI-5124 Specifications  
 
Specification  
Value  
50 Ω  
Comments  
RMS Noise  
Range (Vpk-pk)  
1 MΩ  
Antialias  
filter on  
0.2  
NI PXI-5124:  
112 μVrms  
(0.056% FS)  
NI PXI-5124:  
130 μVrms  
(0.065% FS)  
50 Ω  
terminator  
connected  
to input  
NI PCI-5124:  
126 μVrms  
(0.063% FS)  
NI PCI-5124:  
146 μVrms  
(0.073% FS)  
0.4  
1
200 μVrms  
216 μVrms  
(0.05% FS)  
(0.054% FS)  
500 μVrms  
(0.05% FS)  
510 μVrms  
(0.051% FS)  
2
1.0 mVrms  
1.02 mVrms  
(0.05% FS)  
(0.051% FS)  
4
2.04 mVrms  
2.16 mVrms  
(0.051% FS)  
(0.054% FS)  
10  
5.1 mVrms  
5.2 mVrms  
(0.051% FS)  
(0.052% FS)  
20  
N/A  
10.2 mVrms  
(1 MΩ only)  
(0.051% FS)  
NI PXI/PCI-5124 Specifications  
10  
ni.com  
 
Specification  
Value  
50 Ω  
Comments  
RMS Noise  
Range (Vpk-pk  
0.2  
)
1 MΩ  
Filters off  
50 Ω  
NI PXI-5124:  
114 μVrms  
(0.057% FS)  
NI PXI-5124:  
164 μVrms  
(0.082% FS)  
terminator  
connected  
to input  
NI PCI-5124:  
128 μVrms  
(0.064% FS)  
NI PCI-5124:  
184 μVrms  
(0.092% FS)  
0.4  
1
204 μVrms  
264 μVrms  
(0.051% FS)  
(0.066% FS)  
510 μVrms  
(0.051% FS)  
550 μVrms  
(0.055% FS)  
2
1.02 mVrms  
1.08 mVrms  
(0.051% FS)  
(0.054% FS)  
4
2.08 mVrms  
2.6 mVrms  
(0.052% FS)  
(0.065% FS)  
10  
20  
5.2 mVrms  
(0.052% FS)  
5.5 mVrms  
(0.055% FS)  
10.6 mVrms  
(0.053% FS)  
© National Instruments Corporation  
11  
NI PXI/PCI-5124 Specifications  
 
60 n  
55 n  
50 n  
45 n  
40 n  
35 n  
30 n  
25 n  
20 n  
15 n  
10 n  
5 n  
1 n  
1 k  
10 k  
100 k  
1 M  
10 M  
100 M  
Frequency (Hz)  
Figure 3. Representation of NI 5124 Spectral Noise Density on 0.2 V Range,  
Noise Filter Enabled, 1 MΩ Input Impedance  
–145.0  
–147.5  
–150.0  
–152.5  
1 k  
10 k  
100 k  
1 M  
10 M  
100 M  
Frequency (Hz)  
Figure 4. Representation of NI 5124 Spectral Noise Density on 0.2 V Range,  
Full Bandwidth, 50 Ω Input Impedance  
NI PXI/PCI-5124 Specifications  
12  
ni.com  
 
Horizontal  
Sample Clock  
Specification  
Value  
Comments  
* Internal  
Sources  
NI PXI-5124  
NI PCI-5124  
Sample Clock is  
locked to the  
ReferenceClock  
or derived from  
the onboard  
Internal, Onboard Clock  
(internal VCXO)*  
Internal, Onboard Clock  
(internal VCXO)*  
External, CLK IN (front  
panel SMB connector)  
External, CLK IN (front  
panel SMB connector)  
VCXO  
External,  
PXI Star Trigger  
(backplane connector)  
Onboard Clock (Internal VCXO)  
Sample Rate  
Range  
Real-Time Sampling  
Random Interleaved  
Sampling (RIS)  
* Divide by  
n decimation  
used for all rates  
less than  
(Single Shot)  
3.052 kS/s to 200 MS/s*  
400 MS/s to 4 GS/s in  
multiples of 200 MS/s  
200 MS/s  
For more  
information  
about Sample  
Clock and  
decimation,  
refer to the  
NI High-Speed  
Digitizers Help.  
Phase Noise  
Density, Typical  
<–100 dBc/Hz at 100 Hz  
<–120 dBc/Hz at 1 kHz  
<–130 dBc/Hz at 10 kHz  
10 MHz input  
signal  
© National Instruments Corporation  
13  
NI PXI/PCI-5124 Specifications  
 
   
Specification  
Value  
1 ps rms (100 Hz to 100 kHz)  
2 ps rms (100 Hz to 1 MHz)  
Comments  
Sample Clock  
Jitter, Typical  
Includes the  
effects of  
the converter  
aperture  
uncertainty and  
the clock  
circuitry jitter  
Excludes trigger  
jitter  
Timebase  
Frequency  
200 MHz  
Timebase  
Accuracy  
Not Phase-Locked to  
Reference Clock  
Phase-Locked to  
Reference Clock  
25 ppm  
Equal to the Reference  
Clock accuracy  
Sample Clock  
Delay Range  
1 Sample Clock period  
Sample Clock  
Delay/Adjustment  
Resolution  
5 ps  
NI PXI/PCI-5124 Specifications  
14  
ni.com  
 
Specification  
External Sample Clock  
Sources  
Value  
Comments  
NI PXI-5124  
NI PCI-5124  
CLK IN (front panel  
SMB connector)  
CLK IN (front panel SMB  
connector)  
PXI Star Trigger  
(backplane connector)  
Frequency  
Range  
50 MHz to 210 MHz (CLK IN)  
Divide by  
n decimation  
available where  
1 n 65,535  
50 MHz to 80 MHz (PXI Star Trigger)  
For more  
information  
about Sample  
Clock and  
decimation,  
refer to the  
NI High-Speed  
Digitizers Help.  
Duty Cycle  
Tolerance  
45% to 55%  
Exported  
NI PXI-5124  
NI PCI-5124  
Reference Clock  
Destinations  
CLK OUT (front panel  
SMB connector)  
CLK OUT (front panel  
SMB connector)  
PFI<0..1> (front panel  
9-pin mini-circular  
DIN connector)  
PFI<0..1> (front panel  
9-pin mini-circular  
DIN connector)  
PXI_Trig<0..7>  
RTSI<0..7>  
(backplane connector)  
© National Instruments Corporation  
15  
NI PXI/PCI-5124 Specifications  
 
Specification  
Value  
Comments  
Sample Clock Exporting  
Exported Sample  
Clock Destinations  
* Decimated  
Sample Clock  
only  
Maximum  
Frequency  
Destination  
CLK OUT (front panel  
SMB connector)  
210 MHz  
PXI_Trig<0..6>  
20 MHz  
25 MHz  
20 MHz  
(backplane connector)*  
PFI<0..1> (front panel 9-pin  
mini-circular DIN connector)*  
RTSI<0..6>*  
Phase-Locked Loop (PLL) Reference Clock  
Specification  
Sources  
Value  
Comments  
NI PXI-5124  
PXI_CLK10  
NI PCI-5124  
RTSI 7  
CLK IN (front panel SMB  
(backplane connector)  
CLK IN (front panel SMB connector)  
connector)  
Frequency  
Range  
1 MHz to 20 MHz in 1 MHz increments.  
Default of 10 MHz.  
The PLL Reference Clock frequency must be accurate  
to 50 ppm.  
Duty Cycle  
Tolerance  
45% to 55%  
Exported  
NI PXI-5124  
NI PCI-5124  
Reference Clock  
Destinations  
CLK OUT (front panel  
SMB connector)  
CLK OUT (front panel  
SMB connector)  
PFI<0..1> (front panel  
9-pin mini-circular  
DIN connector)  
PFI<0..1> (front panel  
9-pin mini-circular  
DIN connector)  
PXI_Trig<0..6>  
RTSI<0..7>  
(backplane connector)  
NI PXI/PCI-5124 Specifications  
16  
ni.com  
 
 
CLK IN (Sample Clock and Reference Clock Input,  
Front Panel Connector)  
Specification  
Value  
Comments  
Input Voltage  
Range  
Sine wave: 0.65 Vpk-pk to 2.8 Vpk-pk (0 dBm to 13 dBm)  
Square wave: 0.2 Vpk-pk to 2.8 Vpk-pk  
Maximum Input  
Overload  
7 Vrms with |Peaks| 10 V  
Impedance  
Coupling  
50 Ω  
AC  
CLK OUT (Sample Clock and Reference Clock Output,  
Front Panel Connector)  
Specification  
Output Impedance  
Logic Type  
Value  
Comments  
50 Ω  
3.3 V CMOS  
48 mA  
Maximum Drive  
Current  
Trigger  
Reference (Stop) Trigger  
Specification  
Value  
Comments  
Trigger Types  
and Sources  
Types  
Sources  
Refer to the  
following  
Edge, Window, Hysteresis,  
Video, Digital, Immediate,  
and Software  
CH 0, CH 1, TRIG,  
sections and the  
NI High-Speed  
Digitizers  
Help for more  
informationabout  
what sources are  
available for each  
trigger type.  
PXI_Trig<0..6>, PFI<0..1>,  
PXI Star Trigger, Software,  
and RTSI<0..6>  
© National Instruments Corporation  
17  
NI PXI/PCI-5124 Specifications  
 
       
Specification  
Value  
Comments  
Time  
Resolution  
TDC  
On  
Onboard Clock  
External Clock  
N/A  
TDC = Time  
to Digital  
Conversion  
Circuit  
50 ps  
Off  
5 ns  
TDC  
External Clock Period  
Rearm Time  
10 μs  
Rearm Time  
Holdoff  
Holdoff set to 0  
On  
Off  
2 μs  
TDC  
On  
Onboard Clock  
External Clock  
N/A  
10 μs to 85.899 s  
Off  
2 μs to 85.899 s  
200 × (External Clock  
Period) to  
(232 – 1) × (External Clock  
Period)  
Analog Trigger (Edge, Window, and Hysteresis Trigger Types)  
Sources  
CH 0 (front panel BNC connector)  
CH 1 (front panel BNC connector)  
TRIG (front panel BNC connector)  
Trigger Level  
Range  
CH 0, CH 1  
100% FS  
TRIG (External Trigger)  
5 V  
Trigger Level  
Resolution  
10 bits (1 in 1,024)  
Edge Trigger  
Sensitivity  
CH 0, CH 1  
TRIG (External Trigger)  
3.5% FS up to 50 MHz,  
increasing to 10% FS at  
150 MHz  
0.25 Vpk-pk up to 100 MHz,  
increasing to 1 Vpk-pk at  
200 MHz  
Level  
Accuracy,  
Typical  
CH 0, CH 1  
TRIG (External Trigger)  
0.35 V up to 10 MHz  
4.7% FS up to 10 MHz  
Trigger  
Jitter  
80 ps rms  
Within 5 °C of  
self-calibration  
temperature  
NI PXI/PCI-5124 Specifications  
18  
ni.com  
 
Specification  
Value  
Comments  
Trigger  
Filters  
Low-Frequency  
(LF) Reject  
High-Frequency  
(HF) Reject  
50 kHz  
50 kHz  
Digital Trigger (Digital Trigger Type)  
Sources NI PXI-5124  
PXI_Trig<0..6>  
NI PCI-5124  
RTSI<0..6>  
(backplane connector)  
PFI<0..1>  
PFI<0..1>  
(front panel SMB connector)  
(front panel SMB connector)  
PXI Star Trigger  
(backplane connector)  
Video Trigger (Video Trigger Type)  
Sources  
CH 0 (front panel BNC connector)  
CH 1 (front panel BNC connector)  
TRIG (front panel BNC connector)  
Specific Line  
Types  
Any Line  
Specific Field  
Standard  
Negative sync of NTSC, PAL, or SECAM signal  
TRIG (External Trigger, Front Panel Connector)  
Specification  
Connector  
Value  
Comments  
BNC  
Impedance  
Coupling  
1 MΩ in parallel with 22 pF  
AC, DC  
12 Hz  
AC-Coupling Cutoff  
(–3 dB)  
Input Voltage Range  
5 V  
Maximum Input Overload |Peaks| 42 V  
© National Instruments Corporation  
19  
NI PXI/PCI-5124 Specifications  
 
 
PFI 0 and PFI 1 (Programmable Function Interface,  
AUX Front Panel Connector)  
Specification  
Connector  
Value  
Comments  
9-pin mini-circular DIN  
Bi-directional  
Direction  
As an Input (Trigger)  
Destinations  
Start Trigger (Acquisition Arm)  
Reference (Stop) Trigger  
Arm Reference Trigger  
Advance Trigger  
150 kΩ  
Input Impedance  
VIH  
VIL  
2.0 V  
0.8 V  
Maximum Input  
Overload  
–0.5 V, 5.5 V  
Maximum  
Frequency  
25 MHz  
As an Output (Event)  
Sources  
Start Trigger (Acquisition Arm)  
Reference (Stop) Trigger  
End of Record  
Done (End of Acquisition)  
Probe Compensation (1 kHz, 50% duty cycle  
square wave, PFI 1 only)  
Output Impedance  
Logic Type  
50 Ω  
3.3 V CMOS  
24 mA  
Maximum Drive  
Current  
Maximum  
Frequency  
25 MHz  
NI PXI/PCI-5124 Specifications  
20  
ni.com  
 
 
TClk Specifications  
National Instruments TClk synchronization method and the NI-TClk driver  
are used to align the sample clocks on any number of SMC-based modules  
in a chassis. For more information about TClk synchronization, refer to the  
NI-TClk Synchronization Help, which is located within the NI High-Speed  
Digitizers Help.  
Specifications are valid for any number of modules installed in one  
NI PXI-1042 chassis.  
All parameters set to identical values for each SMC-based module.  
Sample Clock set to 200 MS/s and all filters are disabled.  
For other configurations, including multichassis systems, contact  
NI Technical Support at ni.com/support.  
Note Although you can use NI-TClk to synchronize nonidentical modules, these  
specifications apply only to synchronizing identical modules.  
Specification  
Value  
Comments  
Intermodule SMC Synchronization Using NI-TClk for Identical Modules (Typical)  
Skew  
500 ps  
Caused by clock and analog  
path delay differences  
No manual adjustment  
performed  
Skew After Manual <10 ps  
Adjustment  
For information about  
manual adjustment, refer to  
the Synchronization  
Repeatability Optimization  
topic in the NI-TClk  
Synchronization Help.  
For additional help with the  
adjustment process, contact  
NI Technical Support at  
ni.com/support.  
Sample Clock  
Delay/Adjustment  
Resolution  
5 ps  
© National Instruments Corporation  
21  
NI PXI/PCI-5124 Specifications  
 
 
Waveform Specifications  
Specification  
Value  
8 MB per channel standard  
Comments  
Onboard  
* NI PXI-5124 only  
Memory Size  
(4 megasamples per channel)  
32 MB per channel option  
(16 megasamples per channel)  
256 MB per channel option  
(128 megasamples per channel)  
512 MB per channel option  
(256 megasamples per channel)*  
Minimum  
1 Sample  
Record Length  
Number of  
Pretrigger  
Samples  
Zero up to full Record Length  
Single-record mode  
and multiple-record  
mode  
Number of  
Posttrigger  
Samples  
Zero up to full Record Length  
Single-record mode  
and multiple-record  
mode  
Maximum  
Number of  
Records in  
Onboard  
8 MB/channel  
21,845  
* NI PXI-5124 only  
It is possible  
to exceed these  
numbers if you fetch  
records while  
32 MB/channel  
256 MB/channel  
512 MB/channel*  
87,381  
100,000†  
100,000†  
Memory  
acquiring data.  
For more  
information, refer to  
the NI High-Speed  
Digitizers Help.  
Allocated  
Onboard  
Memory per  
Record  
(Record Length × 2 bytes/S) + 200 bytes, rounded up to  
next multiple of 128 bytes  
or  
384 bytes, whichever is greater  
NI PXI/PCI-5124 Specifications  
22  
ni.com  
 
 
Calibration  
Specification  
Value  
Comments  
Self-Calibration  
Self-calibration is done on software command.  
The calibration corrects for gain, offset, frequency  
response, triggering, and timing adjustment errors  
for all input ranges.  
External Calibration  
(Factory Calibration)  
The external calibration calibrates the VCXO and the  
voltage reference. Appropriate constants are stored  
in nonvolatile memory.  
Interval for External  
Calibration  
2 years  
Warm-Up Time  
15 minutes  
Power  
Specification  
Typical Value  
Comments  
NI PXI-5124  
1.3 A  
NI PCI-5124  
1.3 A  
+3.3 VDC  
+5 VDC  
1.7 A  
2.7 A  
+12 VDC  
–12 VDC  
Total Power  
130 mA  
270 mA  
17.6 W  
130 mA  
0 A  
19.4 W  
© National Instruments Corporation  
23  
NI PXI/PCI-5124 Specifications  
 
   
Software  
Specification  
Value  
Comments  
Driver  
NI-SCOPE 2.7 or later  
Software  
NI-SCOPE is an IVI-compliant driver that allows you to  
configure, control, and calibrate the NI 5124. NI-SCOPE  
provides application programming interfaces for many  
development environments.  
Application  
Software  
NI-SCOPE provides programming interfaces,  
documentation, and examples for the following  
application development environments:  
LabVIEW  
LabWindows/CVI™  
Measurement Studio  
Microsoft Visual C/C++  
Microsoft Visual Basic  
Interactive  
Soft Front  
Panel and  
The Scope Soft Front Panel supports interactive control of  
the NI 5124. The Scope Soft Front Panel is included on the  
NI-SCOPE CD.  
Configuration  
National Instruments Measurement & Automation Explorer  
(MAX) also provides interactive configuration and test tools  
for the NI 5124. MAX is included on the NI-SCOPE CD.  
NI PXI/PCI-5124 Specifications  
24  
ni.com  
 
 
Environment  
NI PXI-5124  
Note To ensure that the NI PXI-5124 cools effectively, follow the guidelines in the  
Maintain Forced Air Cooling Note to Users included in the NI PXI-5124 kit. The  
NI PXI-5124 is intended for indoor use only.  
Specification  
Value  
Comments  
Operating  
Temperature  
0 ºC to +55 ºC in all NI PXI chassis except the following:  
0 ºC to +45 ºC when installed in an NI PXI-1000/B or  
PXI-101x chassis  
Meets IEC-60068-2-1 and IEC-60068-2-2  
Storage  
Temperature  
–40 ºC to +71 ºC  
Meets IEC-60068-2-1 and IEC-60068-2-2  
Operating Relative  
Humidity  
10% to 90%, noncondensing  
Meets IEC-60068-2-56  
Storage Relative  
Humidity  
5% to 95%, noncondensing  
Meets IEC-60068-2-56  
Operating Shock  
Storage Shock  
30 g, half-sine, 11 ms pulse  
Meets IEC-60068-2-27  
Test profile developed in accordance with  
MIL-PRF-28800F  
50 g, half-sine, 11 ms pulse  
Meets IEC-60068-2-27  
Test profile developed in accordance with  
MIL-PRF-28800F  
Operating Vibration 5 Hz to 500 Hz, 0.31 grms  
Meets IEC-60068-2-64  
Storage Vibration  
5 Hz to 500 Hz, 2.46 grms  
Meets IEC-60068-2-64  
Test profile exceeds requirements of MIL-PRF-28800F,  
Class B  
Altitude  
2,000 m maximum (at 25 °C ambient temperature)  
2
Pollution Degree  
© National Instruments Corporation  
25  
NI PXI/PCI-5124 Specifications  
 
   
NI PCI-5124  
Note To ensure that the NI PCI-5124 cools effectively, make sure that the chassis in which  
it is used has active cooling that provides at least some airflow across the PCI card cage.  
To maximize airflow and extend the life of the device, leave any adjacent PCI slots empty.  
Refer to the Maintain Forced Air Cooling Note to Users included in the NI PCI-5124 kit  
for important cooling information. The NI PCI-5124 is intended for indoor use only.  
Specification  
Operating  
Value  
Comments  
0 ºC to +45 ºC  
Temperature  
Meets IEC-60068-2-1 and IEC-60068-2-2  
Storage  
Temperature  
–40 ºC to +71 ºC  
Meets IEC-60068-2-1 and IEC-60068-2-2  
Operating Relative  
Humidity  
10% to 90%, noncondensing  
Meets IEC-60068-2-56  
Storage Relative  
Humidity  
5% to 95%, noncondensing  
Meets IEC-60068-2-56  
Storage Shock  
50 g, half-sine, 11 ms pulse  
Meets IEC-60068-2-27  
Test profile developed in accordance with  
MIL-PRF-28800F  
Storage Vibration  
5 Hz to 500 Hz, 2.46 grms  
Meets IEC-60068-2-64  
Test profile exceeds requirements of MIL-PRF-28800F,  
Class B  
Altitude  
2,000 m maximum (at 25 °C ambient temperature)  
2
Pollution Degree  
NI PXI/PCI-5124 Specifications  
26  
ni.com  
 
 
Safety, Electromagnetic Compatibility,  
and CE Compliance  
Safety  
This product is designed to meet the requirements of the following  
standards of safety for electrical equipment for measurement, control, and  
laboratory use:  
IEC 61010-1, EN 61010-1  
UL 61010-1, CSA 61010-1  
Note For UL and other safety certifications, refer to the product label or visit ni.com/  
certification, search by model number or product line, and click the appropriate link  
in the Certification column.  
Electromagnetic Compatibility  
This product is designed to meet the requirements of the following  
standards of EMC for electrical equipment for measurement, control,  
and laboratory use:  
EN 61326 EMC requirements; Minimum Immunity  
EN 55011 Emissions; Group 1, Class A  
CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A  
Note For EMC compliance, operate this device with RG223/U or equivalent shielded  
cable. Operate according to product documentation  
CE Compliance  
This product meets the essential requirements of applicable European  
Directives, as amended for CE marking, as follows:  
2006/95/EC; Low-Voltage Directive (safety)  
2004/108/EC; Electromagnetic Compatibility Directive (EMC)  
Note Refer to the Declaration of Conformity (DoC) for this product for any additional  
regulatory compliance information. To obtain the DoC for this product, visit ni.com/  
certification, search by model number or product line, and click the appropriate link  
in the Certification column.  
© National Instruments Corporation  
27  
NI PXI/PCI-5124 Specifications  
 
       
Environmental Management  
National Instruments is committed to designing and manufacturing  
products in an environmentally responsible manner. NI recognizes that  
eliminating certain hazardous substances from our products is beneficial  
not only to the environment but also to NI customers.  
For additional environmental information, refer to the NI and the  
Environment Web page at ni.com/environment. This page contains the  
environmental regulations and directives with which NI complies, as well  
as any other environmental information not included in this document.  
Waste Electrical and Electronic Equipment (WEEE)  
EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling  
center. For more information about WEEE recycling centers and National Instruments  
WEEE initiatives, visit ni.com/environment/weee.htm.  
⬉ᄤֵᙃѻક∵ᶧ᥻
ㅵ⧚
⊩ ˄Ё೑  
˅
RoHS  
Ё೑ᅶ᠋  
݇Ѣ  
ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤
Փ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ  
DŽ
National Instruments  
National Instruments  
(RoHS)  
Ё೑  
ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/environment/rohs_chinaDŽ  
RoHS  
ni.com/environment/rohs_china  
(For information about China RoHS compliance, go to  
.)  
Physical  
Front Panel Connectors  
Label  
CH 0  
Function  
Connector Type  
Analog Input  
Analog Input  
External Trigger  
BNC female  
BNC female  
BNC female  
CH 1  
TRIG  
CLK IN  
Sample Clock Input and Reference SMB jack  
Clock Input  
CLK OUT  
AUX I/O  
Sample Clock Output and  
Reference Clock Output  
SMB jack  
PFI 0, PFI 1  
9-pin mini-circular DIN  
NI PXI/PCI-5124 Specifications  
28  
ni.com  
 
     
NI PXI-5124 Front Panel Indicators  
Label  
Function  
For more  
information,  
refer to the  
NI High-Speed  
Digitizers  
Help.  
ACCESS  
The ACCESS LED indicates the status of the PCI bus and the  
interface from the NI PXI-5124 to the controller.  
ACTIVE  
The ACTIVE LED indicates the status of the onboard  
acquisition hardware of the NI PXI-5124.  
Dimensions and Weight  
NI PXI-5124  
Dimensions  
3U, One slot, PXI/cPCI Module  
21.6 × 2.0 × 13.0 cm  
(8.5 × 0.8 × 5.1 in.)  
2.0 cm  
(0.8 in.)  
13.0 cm  
(5.1 in.)  
21.6 cm  
(8.5 in.)  
Weight  
383 g (13.5 oz)  
© National Instruments Corporation  
29  
NI PXI/PCI-5124 Specifications  
 
 
NI PCI-5124  
Dimensions  
35.5 × 2.0 × 11.3 cm  
(14.0 × 0.8 × 4.4 in.)  
2.0 cm  
(0.8 in.)  
11.3 cm  
(4.4 in.)  
35.5 cm  
(14.0 in.)  
Weight  
455 g (16 oz)  
NI PXI/PCI-5124 Specifications  
30  
ni.com  
 
Where to Go for Support  
The National Instruments Web site is your complete resource for technical  
support. At ni.com/support you have access to everything from  
troubleshooting and application development self-help resources to email  
and phone assistance from NI Application Engineers.  
A Declaration of Conformity (DoC) is our claim of compliance with the  
Council of the European Communities using the manufacturer’s  
declaration of conformity. This system affords the user protection for  
electronic compatibility (EMC) and product safety. You can obtain the DoC  
for your product by visiting ni.com/certification. If your product  
supports calibration, you can obtain the calibration certificate for your  
product at ni.com/calibration.  
National Instruments corporate headquarters is located at  
11500 North Mopac Expressway, Austin, Texas, 78759-3504.  
National Instruments also has offices located around the world to help  
address your support needs. For telephone support in the United States,  
create your service request at ni.com/support and follow the calling  
instructions or dial 512 795 8248. For telephone support outside the United  
States, contact your local branch office:  
Australia 1800 300 800, Austria 43 662 457990-0,  
Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599,  
Canada 800 433 3488, China 86 21 5050 9800,  
Czech Republic 420 224 235 774, Denmark 45 45 76 26 00,  
Finland 358 (0) 9 725 72511, France 01 57 66 24 24,  
Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737,  
Italy 39 02 413091, Japan 81 3 5472 2970, Korea 82 02 3451 3400,  
Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710,  
Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466,  
New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60,  
Poland 48 22 3390150,Portugal 351 210 311 210,Russia 7 495 783 6851,  
Singapore 1800 226 5886, Slovenia 386 3 425 42 00,  
South Africa 27 0 11 805 8197, Spain 34 91 640 0085,  
Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151,  
Taiwan 886 02 2377 2222, Thailand 662 278 6777,  
Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545  
© National Instruments Corporation  
31  
NI PXI/PCI-5124 Specifications  
 
 
National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation.  
Refer to the Terms of Use section on ni.com/legal for more information about National  
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade  
names of their respective companies. For patents covering National Instruments products, refer to the  
appropriate location: Help»Patents in your software, the patents.txt file on your CD, or  
ni.com/patents.  
© 2004–2007 National Instruments Corporation. All rights reserved.  
371135F-01  
Aug07  
 

Miele Clothes Dryer T 4463 C User Manual
Miele Convection Oven h 4331 User Manual
Miele Washer W2444WPS User Manual
NEC Washer SAV 4 HD User Manual
Nikon Camera Accessories 4804 User Manual
Nilfisk ALTO Vacuum Cleaner Drum Top Vacuum User Manual
Omega Vehicle Security Switch LV 510 User Manual
Panasonic Electric Shaver ESRF 41 User Manual
Panasonic Network Card MAZC062D User Manual
ParkerVision Digital Camera 1 CCD User Manual